Martin Tool Auto Body Spoons & Dollies
Surfacing Spoon
Excellent spoon for fender spring hammering, finishing and shaping. Curve gets behind inner construction between panels that are close for removal of dents. Molds panels. Blade fully polished. 9” Blade Length. 2 1/8” Width. Overall Length 15 1/8”. Weight 2.5 lbs.
Surfacing Spoon |
|||
MTF-1024 | $35.75 | ||
|
Medium Crown Spoon
Long slender shape just like the 1024 surfacing spoon. Inside with medium crown, for high ridges or prying. For slapping and surface finishing on fenders, panels and trunk lids. Blade fully polished. 9” Blade Length. 2 1/8” Width. Overall Length 14 7/8”. Weight 1.5 lbs.
Medium Crown Spoon |
|||
MTF-1026 | $36.00 | ||
|
Light Dinging Spoon
To ding ridges smooth and level. When held against ridge and struck with hammer, spreads blow over large area making smooth job and preventing damage to metal or finish. Not made for prying. Length 10” overall. Face 2” x 4 5/16”.Weight .50 lbs.
Light Dinging Spoon |
|||
MTF-1036 | $25.75 | ||
|
Heavy Duty Double End S-Spoon
General purpose fender and frame spoon. Designed to provide further reach on panels and behind reinforcements. Prying, heavy duty design for use on SUV frames. 12 3/16” Length. 1 3/8” x 5 ¼” Face. Weight 3.0 lbs.
Heavy Duty Double End Spoon |
|||
MTF-1044 | $65.75 | ||
|
Combination Spoon
General purpose fender spoon. Used as dolly behind brackets, inner panels and similar places. Handle offset to give balance when dinging and for long reach. Has high-crown working surface. Face 1 ¾” x 5 ½”. handle 1” octagon 4 ¾” long. Weight 3.0 lbs.
Combination Spoon |
|||
MTF-1050 | $47.50 | ||
|
Spoon Dolly
Long handle permits many uses in places otherwise inaccessible. Can be driven between reinforcements and outer panel, then used to pry outward as the metal is dinged. Excellent forming and caulking tool for the deep pockets of doors, quarter-panels, rear fenders and lower trunk panels. Size 2 ½” x 1” x 3”. Weight 4.2 lbs.
Spoon Dolly |
|||
MTF-1052 | $48.25 | ||
|
Long Curved Spoon
Long, thin, curved blade is handy for prying up dents behind curved reinforcements in header panels, hinge anchors in doors, body pillars and reinforcements in hoods and radiator shells. Length 10 ½” overall. Face 2” x 7”. Weight 1.5 lbs.
Long Curved Spoon |
|||
MTF-1054 | $35.50 | ||
|
Wing-Ding Spoon Dolly
The answer to repair problems on high fins. A dolly, a spoon, a pry. Long handle and special contours for working up inside cramped fins. Wide spoon transmits hammer blows over wide area without damaging finish. 1” handle diameter, 19” overall length. Weight 4.5 lbs.
Wing Ding Spoon Dolly |
|||
MTF-1056 | $63.25 | ||
|
Light Weight Toe Dolly
Designed for flat surfaces. All the features of a toe dolly. Sizes 4 ¾” x 2 ¼” x 11/16”. Weight 1.8 lbs.
Light Weight Toe Dolly |
|||
MTF-1057 | $50.25 | ||
|
Toe Dolly
Thinness and length provide easy accessibility to narrow pockets. Large, flat face is frequently used in shrinking and dinging flat panels. The flat sides furnish a convenient anvil for repairing flanges. Sizes 4 ¾” x 2 3/8” x 1 1/8”. Weight 3.0 lbs.
Toe Dolly |
|||
MTF-1058 | $50.25 | ||
|
Heel Dolly
Design makes it possible to reach easily into sharp corners and wide radii. These features are exclusive to the Heel Dolly and continue its high demand. Sizes 3 ¼” x 2 ½” x 1 7/16”. Weight 2.7 lbs.
Heel Dolly |
|||
MTF-1059 | $42.25 | ||
|
General Purpose “Track” Dolly
Provides convenient and comfortable hand hold during heaviest blows. Weight, balance and several differently crowned working faces, together with two beading and flange lips, give this dolly broad general use. Sizes 2 7/8” x 2 3/8” x 2 ¼”. Weight 3 lbs.
General Purpose "Track" Dolly |
|||
MTF-1060 | $51.25 | ||
|
Utility Dolly
High-crown dolly with one narrow beading edge. Thick rounded sides are useful in short radii curves. Wide application of uses in high-crown portions of hoods, fenders and body panels. Sizes 3 1/8” x 3 x 5 5/8”, Weight 2.9 lbs.
Utility Dolly |
|||
MTF-1061 | $45.25 | ||
|
Egg Shaped Dolly
This unique shape with high crown design is a very popular shape, with many different curves and angles. Sizes 1 5/8” x 2 ½” x 3 ¾”. Weight 3.1 lbs.
Egg Shaped Dolly |
|||
MTF-1064 | $49.50 | ||
|
Light Weight Wedge Dolly
Short, slender general purpose dolly. Good hand grip. Also used for beads or flanges on fenders. Thin edge is useful for corners and beading. Flat side works under long curve of fender. Size 2 7/64” x 2 ½” x 4 27/64”. Weight 2.7 lbs.
Light Weight Wedge Dolly |
|||
MTF-1065 | $35.75 | ||
|
Wedge Dolly
Long, slender general purpose dolly. Widely favored by many body repair men for all-around use. The long, thin lip is very useful in working behind reinforcements. Sizes 5 ¾” x 2 3/8” x 2 3/16”. Weight 4 lbs.
Wedge Dolly |
|||
MTF-1067 | $51.25 | ||
|
Low Crown Dolly
Specially designed for use on low-crown panels where medium and high-crown dollies would stretch the metal. Angle between the sides and large face is less than 90°, which permits this dolly to reach into the corner of a flanged edge. Sizes 3 7/8” x 2 ¾” x 1 5/8”. Weight 3.3 lbs.
Low Crown Dolly |
|||
MTF-1068 | $49.50 | ||
|
“Champion” Heavyweight Dolly
Heavy duty, general purpose fender dolly. A necessity on heavy gauge fenders which resist the blows of lighter dollies. Brings out the toughest damage. Seats comfortably in the hand and protects fingers from a swinging blow. Sizes 3 3/8” x 3 3/8” x 2 11/16”. Weight 4.6 lbs.
"Champion" Heavy Weight Dolly |
|||
MTF-1070 | $69.50 | ||
|
Heavy Duty Driving & Fender Bending Tool
Useful for restoration of turned under, non-wired flanged edges. Also handy for alignment of inner construction and flanges on alligator hoods. Heavy formed striking pads. Length 14 1/8”. Weight 3.2 lbs.
Heavy Duty Driving & Fender Bending Tool |
|||
MTF-1091 | $75.00 | ||
|
Caulking Iron
Excellent precision-made wire caulking iron. Polished working surfaces are rounded for use on inside moldings. Face 1 ¾” x 1 “. Overall length 11”. Weight 1.4 lbs.
Caulking Iron |
|||
MTF-1096C | $36.25 | ||
|